Global Polytec Ltd.,Part.

Posts Tagged ‘plastic’

Question by Flight: How is this plastic product made?
http://average-dudes.com/wp-content/uploads/2008/02/n-ice_rack_overhead.jpg

I’m looking to have a similar product manufactured, and need to know what process is used to create this type of product. It is a hard plastic that is meant to be filled with water and frozen to make drinks cold. The space inside is hollow. Is this Injection molded?

Best answer:

Answer by Mr. X
This product is definitely injection molded.

Give your answer to this question below!

Question by KOKO: Does health insurance cover plastic surgery, such as a chin implant?
Also, how much is the average cost for a chin implant in the los angeles area… and do you recommend chin injections over regular plastic surgery? thanks

Best answer:

Answer by catcherinthelight00
I don’t think so…

What do you think? Answer below!

Question by shadfurman: what is the black plastic screw on the bottom of the throttle body of my ’86 volvo 240 dl?
I have an ’86 volvo 240 dl (B230F engine w/LH 2.2 injection) there is a black adjuster screw on the bottom of the throttle body, what does that do?

Best answer:

Answer by David S
It is part of the idle speed control. On the fender above the battery you will find a plug with two wires that is not plugged into anything. If you ground one of the wires,I don’t remember which one, the idle speed will drop to it’s base setting. While idling at the base setting,turning the knob will allow you to raise or lower the base setting. Usually you set the base idle to where the motor is idling around 650-700 rpm. Un- grounding the connector should cause the idle to rise momentarily and then settle down to around 750 -850 rpm.

Know better? Leave your own answer in the comments!

Question by ken: Through what plastic forming process are plastic casings of televisions and monitors formed?
Is it injection molding?

Best answer:

Answer by doug_donaghue
Usually it’s injection. If you look closely you can generally find where the sprues were trimmed off and see a few nit lines. But it’s also possible to use sheets of thermosetting plastic and fairly large hot molds for some parts.

HTH,
Doug

Know better? Leave your own answer in the comments!

Question by gib g: Is it dangerous to work in a plastic factory and breathe in the air expelled by the machines? AOKI?
The factory has extrusion blow molding, injection, and stretch blow molding machines such as AOKI DIRECT HEATCON Stretch blow molding machines. Is it ok to breathe in the air expelled by these machines and are there any real dangers to working in a plastic factory overall? By the way the plant is called BERRY PLASTICS

Best answer:

Answer by Jules
Yes, it is VERY dangerous. I would be very careful if I was you

Know better? Leave your own answer in the comments!

John gets scientific and blinds with us a rundown on the various materials our models are made from
Video Rating: 4 / 5

www.guvenplastic.com Güven Plastik is located in İzmir, Turkey, which manufactures variety of products that consist of PPRC pipes, irrigation systems, PVC profiles, hoses, LDPE pipes and their fittings. The products, which we manufacture are our vast experience in plastic extrusion and injection methods. Our products have Turkish Standart Approvals and we have been in the market for the past 40 years. For a possible business co-operation, we can offer quality as well competitive solutions to your needs.
Video Rating: 0 / 5

Question by Keline: why more and more Chinese girls fancy plastic surgeries?
More and more Chinese girls who just finished their degrees go for plastic surgeries, i.e. nose job, lip injection, double eyelid operation etc. They say they try to have an upper hand in the fiercely-competitive job hunt. Does look count so much?

Best answer:

Answer by perfectlybaked
Well, more and more of them can afford it.

As far as jobs go, well, I don’t think looks have a direct correlation, but in such a crowded market as they have over their, I’m sure anything extra will help.

Add your own answer in the comments!

Question by Trenisha: Do plastic surgeons believe in physical perfections?
i dont know. i was watching a show and it talked about this guy who was a plastic surgeon. and he had this wife who looked like she was an advertisment for plastic surgery. breast implants, lip injection, etc…and it got me wondering, do plastic surgeons believe in physical perfections? if they do, do they want their girlfriend/wife/whatever to be physically perfect? like i said, this question just popped into my head so i thought i would ask it. what do you think?

Best answer:

Answer by MistressDolly
They hope for the contrary, I’m sure! Have fun. MistressDolly

Give your answer to this question below!

Question by plandai2003: Hi,Please explain : the extrude mold and injection mold method in plastic industry. Thanks so much.?
– Finished products to be made from these two methods.
– Can one method used to replace for the orther.
– For the PET material, what products will be made from these two method.
– Process of these two method

Best answer:

Answer by simsjk
Extrusion.. There is a mold or tooling which the molten plastic is forced through to produce a continuous shape.. Extrusion is used to make Plastic window frames, plastic bags, guttering, plastic tubing etc.
Injection.
There is a closed mold or tool which molten plastic is injected into, solidified and then removed.
For example the fittings that you use to fix your guttering to your roof, the dashboard of your car, , the soles of your shoes.. I.e. complex shapes that require dimensions in X, Y and Z axes whereas the Extruded only needs the X and Y axes.

Add your own answer in the comments!

Watch the journey of a plastic granule from the silo, to the dryer, into a gravimetric blender, and then into the processing machine. This type of system is used to supply the raw material into injection moulding machines which make things like moblie phone or tv cases, blow moulding machines which make plastic bottles, and extruders which make things like plastic pipe.
Video Rating: 5 / 5