Global Polytec Ltd.,Part.

Posts Tagged ‘know’

Question by radha k: please let me know the process of recycling of EVA waste produced from injection moulding machines. as i have
know detailed process of recycling of EVA waste.

Best answer:

Answer by odysseus1959
I don’t understand your question.

At Flexible Products Corp. we have started to sell(?) our vulcanized urethane waste/runners to a recycler.

Even if we just gave it them, its better than the land fill.

Give your answer to this question below!

Question by Alex: I want to know the basic principle of Injection moulding and its process.?

Best answer:

Answer by up all night
plastic or some resin is melted in a barrell and mixed via an auger. forming dies (whatever form you are molding) are at the end of the barrell. hydraulic or electric rams hold the forms in place and the mold is filled with melted compound.

What do you think? Answer below!

Question by june yi: anyone know how to rework scratched surface of plastics?
any solution for rework the surface of plastic (polyurethene) after injection molding?

Best answer:

Answer by Move on
Very fine buffing compound and electric buffer with time and patience.

Give your answer to this question below!

Question by JALISCO: Have 77 ford -351m nice clean truck, looking to restore and would like to know about fuel injection options?
as well as companys that offer upgrade parts for this type of engine,these old ford trucks are all steel and tuff as nails no plastic junk ,but they love gas, so far i have looked at a offenhouser intake that claims to improve fuel economy, i was thinking maybe to mix a newer aluminum intake with a factory fuel rail injection system and wire in the computor and other parts from a later model truck motor, i realize i would have to boar the holes for the injectors and build the air inlet control parts from other units, but all in all can this be done and what other problems could i run in to, also the fire to the plugs ? maybe a mag type distributor or what, iv’e had this truck since back when i was in school and really want the mpg to improve as well as dependable for long trips, later i want to give to my son when everything is problem free, if anyone out their can give me solid info it would really make my day, thanks so much for your help.

Best answer:

Answer by rakel-de-freitas@rogers.com
Your best bet is to obtain a “donor” vehicle. Get a wrecked 2000 and up F-series truck with let’s say a 5.4L SOHC V8 with a 4R100 transmission. That would be an EXCELLENT combination. The horsepower & torque of that drivetrain would easily surpass your 351M. Just make sure you get EVERYTHING, and wire it in accordingly. You could even fabricate your suspension to accept the 4-wheel disc brake set-up depending how handy and creative you are. Hope this helps.

Know better? Leave your own answer in the comments!

Question by dabigdoggy: does anybody know anything about a company called Encon Inc.?
I was offered a job with there company but would like to know if it is a solid company to work for and what kind of benefits they have.I already know that it is a plastic mold injection operation.

Best answer:

Answer by Mariposa
I have not heard of Encon. There is a company called Econ which is listed in the Wall Street Journal.

What do you think? Answer below!

Question by michelley: Does Anyone Know The Affects Of Receiving A Parvo And Dirty Syringe Injection?
In May/2000 i was vaccinating a sow with “Porcine Parvo” about 10cc’s and a very dirty syringe caked on the inside with old vaccines. I received the vaccine through a 15 guage needle gun,which punctured through my left hand and damaged nerves and my tendon sheeth. I was then rushed to hospital for treatment as i was unable to use my left hand,not to mention the severe pain. I was sent home that night and checked in with them the next 3 days and on the fourth i was admitted to the hospital as i became very ill. The plastic surgeon talked about amputating my hand,i refused and my hand got better enough to not loose my hand but i still had pain and problems. NO DOCTOR knew what to do or what it would do to me,out of the hospital and still searching my options. I had numerous tests done and finaly an MRI on my left hand which showed up a mass on my nerves and tendon sheeth. July/2002 i had hand surgery to remove the mass BUT i am still suffering . Can anyone help with some answers?? Thanks

Best answer:

Answer by Curious
Maybe you were being told that just because it’s an animal you are injecting, they should be given a clean syringe

What do you think? Answer below!

Question by parmar shashikant r: i wanna know about first injection moulding machine in india?
or hys tory of injection moulidng machine in india plastic injection moulding machine in india

Best answer:

Answer by sr71_usaf
Check this out:

http://www.alibaba.com/countrysearch/IN-suppliers/Moulding_Machine.html

http://www.india-berlin.com/us/e-chronik.htm

What do you think? Answer below!

Question by wbski: how do you know when a diesel injection pump is going bad?
acts like its running out of fuel,but its not ,its getting plenty,lots of air bubbles in the return line when it starts acting up.I’ve had so much trouble that I used clear plastic lines so I could see whats going on.could it be the injection pump?sometimes it runs fine for days and then bingo its back.

Best answer:

Answer by busnuttwo
you have air geting into fuel system from where ? you did not not list car or engine so hard to help more but air in return to tank means air is comming some where

Add your own answer in the comments!

Question by hopefull: Dose any one know the name of the plastic injections that helps prevent pregnancy that’s advertised on tv?
Has anyone used this method of pregnancy prevention? How is it done? Can you feel it during sex? Dose it mess with your period?

Best answer:

Answer by Baby Boy Coming 9/15/09!!!
… I guess you’re talking about an IUD.

What do you think? Answer below!

Question by pamela_hoang: anyone know who is supplier of plastic injection molding machine from Thailand?
pls. i want to buy an injection machine, if know please introduce me or webpage of that section

Best answer:

Answer by itvcharter
Try Pico International Inc.

What do you think? Answer below!